Procedure: - Incision - Flap Design - Application of the template - Implant Placement - Suture - Application of the provisionary Materials: E-Woo Picasso Trio: Digital Panoramic, Cephalometric and Dental CT (3in1)

Procedure: - Topographic anatomy of the palate - Localization of the palatal implant site - Surgical insertion of the palatal implant - Surgical insertion of the cortical screws - Examples of the orthodontic devices Materials: Palatal Implant (Straumann, Orthosystem) and Screw (Aarhus System, Medicon)

Overview - Incision technique - Flap creation - Transplant fixation - Suture closure Contents: This video demonstrates the coverage of multiple recessions by means of a modified tunneling technique characterized by the use of a minimally invasive, atraumatic procedure without the creation of vertical incisions

Overview: Part 1 - Incision and mobilization of the mucoperiosteal flap - Cleaning the bony defect - Screw insertion for support, membrane application and fixation - Suture closure Part 2 - Opening of the mucosa above the region of augmented bone - Preparation of tunnel and bone bed for an open screw-type endosteal implant (Straumann® implant) - Use of single button sutures for tension-free wound closure Contents: This female patient presented with bone loss due to a radicular cyst at tooth 27 and peri-implantitis at tooth 26. Four months after extraction of the respective tooth and implant, guided bone regeneration (GBR) was carried out using supporting screws and an e-PTFE membrane for augmentation of the posterior tooth region of the maxilla. Four months after GBR the insertion of an implant took place.

Overview: - Periodontal and implant planning - Treatment of a horizontal and vertical bone defect - discussion of the literature - Clinical implementation of bone augmentation using a bone block and treatment of a vertical pocket with Emdogain - Sinus lift in combination with alveolar ridge augmentation and horizontal expansion of the alveolar process; orthodontic straightening of a molar tooth Contents: This contribution illustrates a complex periodontal-implantological case, from treatment planning to clinical implementation. It details the transplantation of two bone blocks from the linea obliqua of the angle of the jaw to the anterior front tooth region, the treatment of a vertical bone pocket with Emdogain, the straightening of a molar tooth using orthodontic mini-implants, and a sinus lift together with alveolar ridge augmentation in the maxillary region using a piezo surgical technique.

Procedure: - Presentation of procedure for immediate implant loading in the edentulous mandible according to the Ledermann concept - Surgical implantation of XIVE® TG implants - Bite registration and impression-taking - Presentation of prosthetic components - Fitting and passive fixation of the mesostructure in the mouth - Integration procedure Contents: This video demonstrates the extraction of teeth in a partially dentate mandible followed by immediate loading of six XIVE® TG implants. Following the Ledermann immediate loading concept, a mesostructure will be used for tension-free primary interlock in this special case. Bridge-like lower full dentures with plastic teeth will then be inserted on this frame and retained with an occlusal screw. Since the dentures can only be removed by the dentist, they are \fixed\ as far as the patient is concerned. This simple and quickly produced yet extremely well-fitting restoration, which requires only minimal time and effort for the implant components, is the subject of this contribution.

Procedure: - Incision Technique 36, 44 - Gentle Flap Mobilization - Pilot Hole Preparation using a CT Template - Sequential Preparation and Implantation - Bone Removal and Augmentation - Wound Closure Contents: Systematic Total Rehabilitation is very challenging, especially in patients with Periodontal Disease with Loss of Supporting Structures. Precise Treatment Planning is essential. The Treatment of Periodontal Disease begins after Conservative Pretreatment. It is not possible to predict the Soft Tissue Esthetic Outcome before the Healing Process is completed. We selected Endosteal Implants for the Augmentation of Lost Support Zones in this Atrophic Mandible. A Three-Dimensional Analysis was performed as the Basis for Navigated Implantation. After Completion of the Periodontal Treatment and Implantation, the patient must wait for approximately 6 months for the Completion of the Healing Process before Prosthetic Reconstruction Procedures can be initiated.

Procedure: - Case evaluation - Incision technique - Implant placement - Membrane adjustment and fixation - Introduction of replacement material - Flap mobilization - Suture technique Contents: Implantation was desired for replacement of a missing upper canine tooth and the adjacent lateral incisor tooth. The initial case evaluation revealed a relatively narrow gap between these two teeth in addition to extensive hard and soft-tissue defects. We selected an incision technique that made it possible to do the augmentation work yet subsequently achieve a tension-free flap closure. Since the bony defect was large while the available space was limited, we had to go for the best possible compromise in regard to implant insertion. After the implants had been inserted, augmentation was carried out using a non-absorbable, titanium-reinforced membrane, bone replacement material, and an absorbable membrane. Extreme flap mobilization was needed to achieve flap closure. An optimal suture technique was used to complete the surgery.

Procedure: Delayed loading of dental implants in the esthetic zone of the maxilla. Guided bone regeneration (GBR) for compensatory augmentation with subsequent exposure after healing. Contents: Soft and hard tissue loss leads to esthetic problems, even in patients with successful implant osseointegration. Delayed loading of dental implants in the esthetic zone is frequently indicated in dental practice, for example, in patients with congenital absence of the lateral incisors. Dental implants can solve this problem. Depending on the extent of hard tissue loss, it may be necessary to perform guided bone regeneration (GBR) in order to achieve better esthetic results. Depending on the degree of atrophy, GBR may be performed before or simultaneous with implantation. Correct implant placement is essential to achieving the end goal: an esthetically pleasing and natural result. In this film and in the presentation, we will demonstrate in detail the procedure for placing implants in this esthetically sensitive region. In addition, we will demonstrate a method of impression-taking that provides dental laboratories a better foundation for achieving excellent esthetic results.

Procedure: - Extraction - Implant Site Drilling and Implant Placement - T-Adapt Insertion Contents: This live operation starts with the extraction of tooth 12, which was loosened and damaged by trauma. Pin fixation was not possible, and a significant loss of distal papillary substance was observed. We therefore elected for placement a 4.5 mm conical Astra implant. After completion of the implant site drilling and the implant placement, a T-Adapt was inserted to shape and support the mucosa. A temporary crown was inserted chairside and left in place for 3 months.

Procedure: - Incision Technique and Roll Flap Creation - Excision and Transplantation of Connective Tissue Graft Material from the Palate - Implant Placement and Fixation Procedure Contents: This video describes the preparation of an implant insertion site for placement of an individual implant at site 11 using a roll flap and free connective tissue graft technique. The procedure is designed to shape the implant insertion site and to create a secure, keratinized gingival base. Step-by-step, the operator demonstrates the incision technique, the roll flap creation procedure and the techniques used for excision, transplantation and fixation of the free connective tissue graft within the scope of implant placement.